Follow Slashdot blog updates by subscribing to our blog RSS feed

 


Forgot your password?
Close
typodupeerror
×
Power Hardware Technology

HydroICE Project Developing a Solar-Powered Combustion Engine 144

Posted by samzenpus from the here-comes-the-sun dept.
cylonlover writes "OK, first things first – stop picturing a car with solar panels connected to its engine. What Missouri-based inventors Matt Bellue and Ben Cooper are working on is something a little different than that. They want to take an internal combustion engine, and run it on water and solar-heated oil instead of gasoline. That engine could then be hooked up to a generator, to provide clean electricity. While that may sound a little iffy to some, Bellue and Cooper have already built a small-scale prototype."
This discussion has been archived. No new comments can be posted.

HydroICE Project Developing a Solar-Powered Combustion Engine More

HydroICE Project Developing a Solar-Powered Combustion Engine

Comments Filter:

  • Separating oil and water which have been mixed at such a fine level doesn't seem the easiest. While I know it can be done, can it be done in such a manner to maintain any of the heat energy which remains? Or does one just accept that energy as lost?

    • Re: (Score:1)

      by Anonymous Coward

      ..could be used to preheat the water which is to be injected i suppose

      • Re: (Score:3)

        by Gorobei ( 127755 )

        seems stupid, though: we have good heat-exchangers that don't require mixing the two fluids. Just coiled metal pipes (add fins if needed) would do the trick.

        We've been building liquid sodium/water exchangers for nuke plants for years. There is zero reason to mix the fluids and then add a separator (which is a real pain in the ass given the oil is in a closed cycle.)

        • Re:On the oil/steam separator... (Score:4, Interesting)

          by TubeSteak ( 669689 ) on Sunday November 25, 2012 @11:22AM (#42087325) Journal

          seems stupid, though: we have good heat-exchangers that don't require mixing the two fluids. Just coiled metal pipes (add fins if needed) would do the trick.

          The point of mixing the fluids is that you cannot otherwise impart enough heat to flash boil the water.
          Not to mention that it's really hard to do what you're suggesting inside the cylinder

          There is zero reason to mix the fluids and then add a separator (which is a real pain in the ass given the oil is in a closed cycle.)

          The whole point of their technique is that they create steam inside the strongest part of an engine.
          As it turns out, oil and water will try to separate on their own, which makes this a less than complicated issue.

          • The point of mixing the fluids is that you cannot otherwise impart enough heat to flash boil the water.

            That begs the question, can you not otherwise impart enough heat to flash boil the water? Why not a big metallic thermal load, made out of recycled popcans?

            • Re: (Score:2)

              by paiute ( 550198 )

              The point of mixing the fluids is that you cannot otherwise impart enough heat to flash boil the water.

              That begs the question, can you not otherwise impart enough heat to flash boil the water? Why not a big metallic thermal load, made out of recycled popcans?

              That's not begging the question.

            • Not really. How can you make the transfer of heat more efficient between two liquids by separating them? Especially when one of them is being turned into a gas, which would act as an insulator between the separating surface and the rest of the liquid.

            • Re: (Score:2)

              by maeka ( 518272 )

              can you not otherwise impart enough heat to flash boil the water? Why not a big metallic thermal load, made out of recycled popcans?

              I believe the trick here is that because you're injecting the "fuel" (liquid water) and injecting the heat source you are able to very precisely control the timing of the engine as well as control the steam's wave front. If you had a static heat source inside the engine there's not only the question of how you deliver heat to that, but also how you control triggering of the p

          • Re:On the oil/steam separator... (Score:4, Insightful)

            by Gorobei ( 127755 ) on Sunday November 25, 2012 @11:51AM (#42087509)

            seems stupid, though: we have good heat-exchangers that don't require mixing the two fluids. Just coiled metal pipes (add fins if needed) would do the trick.

            The point of mixing the fluids is that you cannot otherwise impart enough heat to flash boil the water.
            Not to mention that it's really hard to do what you're suggesting inside the cylinder

            That is just not true. Look at a steam catapult, or a pressure cooker, or even a classic rail locomotive. You just need a boiler under some pressure.

            There is zero reason to mix the fluids and then add a separator (which is a real pain in the ass given the oil is in a closed cycle.)

            The whole point of their technique is that they create steam inside the strongest part of an engine.
            As it turns out, oil and water will try to separate on their own, which makes this a less than complicated issue.

            "Trying to separate" is a lot different from actually separating. Heat a pan of oil to 400 degrees in your kitchen, now dribble water drops onto the oil for a minute or two. Notice how greasy your kitchen tops are getting? Heat transfer == physical motion in liquids == oil in your steam.

            How do you plan to separate the stream/oil droplet mixture? Do simple experiment: shake a pint of cooking oil and water together. How long did they take to separate back out? 1 hour to get to 95%? Now try it at high temperatures: you are talking days unless you have a serious refrigeration unit in your engine.

            • How do you plan to separate the stream/oil droplet mixture? Do simple experiment: shake a pint of cooking oil and water together. How long did they take to separate back out? 1 hour to get to 95%? Now try it at high temperatures: you are talking days unless you have a serious refrigeration unit in your engine.

              Oil and water separation is a solved problem.

              "How" depends on the volume of emulsion, the available space and power.
              Maybe they'll use a centrifuge. Maybe electrostatic separation.
              Maybe they'll heat the oil with a peltier and use the cool side as "a serious refrigeration unit".

              I'm not an engineer and even if I was, TFA doesn't provide enough information to 100% answer your question.
              But like I said, it's a solved problem.

              • Maybe they'll use a centrifuge. Maybe electrostatic separation.
                Maybe they'll heat the oil with a peltier and use the cool side as "a serious refrigeration unit".

                All of those take energy that would sap the efficiency of the system. I'd probably go with a large condensation box that has baffles in it like a septic tank to keep disturbances down. As the liquids cool and travel through/around the baffles, they're slowed and turbulence is minimized.

                You might not need a 100% efficient separation system to make it work.

                Still, I don't see it being more efficient at this point than traditional steam engines and turbines.

            • You would probably use an electrocoalescer. It's very commonly used in the oil industry, where water and oil is mixed into an emulsion in the wellhead choke valve. (An electrocoalescer is a fancy name for a tank with an applied electric field, either AC or DC, of around 10-100 kV/m.)

          • Re: (Score:2)

            by Herve5 ( 879674 )

            In my early years I did a bit of basic motorcar repairing. Nothing ambitious.
            One obvious issue for all, was that whenever a watercooled motor got a leak between oil and water, the result was *mayonnaise*, a compound of oil and water which DEFINITELY won't separate "on their own" --just try it: get a mayonnaise cup, and watch it separating ;-)
            At that time basically the motor was dead.
            Now, I understand there may be ways to try separating. Maybe.

        • There is one, oil/steam mixtures are ferociously combustable, and would easily allow one to burn diesel or even used engine oil in an spark ignitioned internal combustion engine; but even that seems a little like a Rube Goldgerg machine to me. There are people who are working on converting the Detroit Diesel Series 71 [wikipedia.org] engines to steam operation, a two cycle diesel would seem fairly easy to convert.

        • Re: (Score:2)

          by dbIII ( 701233 )

          We've been building liquid sodium/water exchangers for nuke plants for years.

          Yes, and the Russians may get it right this time with the reactor they have under construction. I'm a bit disgusted that you are trivilising it as if it is a common thing and as if they are not major maintainance problems and pretending you know what you are writing about. The French had to rebuild such systems from scratch several times for Superphoenix and their final result is the current state of the art.

    • If you use a small amount of oil to flash a relatively large amount of water you would get better efficiency, but you'd need to heat the oil to higher temperatures which brings its own problems. Also separating oil and water is easy, seeing as they don't actually mix.

      • Re: (Score:2)

        by maeka ( 518272 )

        Also separating oil and water is easy, seeing as they don't actually mix.

        The oil is assuredly atomized to increase surface area and heat transfer, seeing as the timing of such an engine depends on precise (and rapid) water phase change. Much like a diesel engine you're relying on very precise injection timing and predictably fast burning/expansion.

        A oil/water mixture composed of such tiny droplets is not trivial to separate.

        • But, how much separation do you really need? From RTFA, I don't think that having oil mixed with the injected water would cause any problems. It would decrease the efficiency, but I would imagine that you could get the oil concentration below 5% pretty easily. And, at those concentrations it seems that the effect on efficiency would probably be negligible.

    • Only the water turns to steam.. Explosively. It'll be floating above the oil, one would think.

    • Re: (Score:3)

      by hawguy ( 1600213 )

      Separating oil and water which have been mixed at such a fine level doesn't seem the easiest. While I know it can be done, can it be done in such a manner to maintain any of the heat energy which remains? Or does one just accept that energy as lost?

      Wouldn't you just cool it below the vapor temperature of the oil and/or water then separate it as liquids? A lot of the will be lost, but not all. Some of the energy can be recaptured by preheating the liquid water and oil.

      They're going to have to cool and return at least the water back to liquid state anyway before it can be injected again for the next cycle.

  • It is in fact a steam engine, using solar-heated oil to flash water to steam right in the cylinder.

    And since TFA can't be arsed to state a single reason why one might choose this over, say, a Stirling heat engine, I'm going to assume there's no good ones.

    • Yes, they have reinvented the steam engine.
      In this case, literally: it runs on stream. (As opposed to many more modern heat engines, which usually use other working fluids).

      The innovation seems to be that they have separated the heat absorption from the expansion of the working fluid.

      If the best they can do is 15%, it will not be competitive with photovoltaic, ever. This needs tracking and mirrors, and that kind of moving parts just can't beat the production efficiencies of silicon solar cells.

      • The only reason this MIGHT compete with solar is the ability to store the thermal energy overnight. Storing heat (as molten salt or hot oil) is easier and less expensive than batteries to store electricity.

        That said, this seems like an awfully inefficient way to go about it and there are already solar thermal plants of different varieties that are commercial-scale, more efficient and less Rube Goldberg-y. I can't see any sensible way to get the oil out of the cylinder without high pressure purge, and if the

      • According to TFA 15% is the same efficiency as photovoltaic but the cost of the system is supposed to be 1/3 of equiv photovoltaic.

        • According to TFA 15% is the same efficiency as photovoltaic but the cost of the system is supposed to be 1/3 of equiv photovoltaic.

          Yes, they said that, but they're wrong. No possible way it can get down to 1/3 the cost of photovoltaic panels. I frankly doubt if they can make it as low as twice times the cost of photovoltaic.

          On a large enough scale, I think a Brayton engine might make it cheaper than photovoltaic, but part of that is because of the high efficiencies, and the other part the economy of scale of large turbines. I doubt a piston engine can be that cheap, not operating at these temperatures.

          Maybe they're thinking about the

        • You really have to take into account potential reduction in costs for any technology meant to compete with photovoltaics (not saying this doesn't have that potential).

          • The cost for X amount of steel, y amount of machining, z for mirrors, etc...

            The costs for PV panels has dropped substantially. At this point I think that only large scale thermal solar will beat it's economy.

    • Interesting that the OP got instantly modded down. Suppose the article was about a new computer language and the article described it as a compiler when it really was an interpreter. Bullshit would be called immediately. Same level of error, different tech.
  • While the engine may ideally just vaporize the water with hot oil, the reactions involved would eventually degrade the oil. Additionally, the separations processes are often 50% of the whole system's energy requirements, I just wouldn't see the viability of such a system. Now a heat exchanger for hot oil/water vaporization would wake a lot more sense, but it seems they want to generate a funding buzz with an internal engine spin.

    • This could probably happen on the way back to the solar collector as the oil is heated back up, then you would just have to condense the steam back into water. Most of the steam would likely just exhaust on its own, but what's trapped in the oil would come out once it's reheated.

      Cheers

  • It's not being burned, it's only being used as a heat carrier. Seems to me it would be more efficient to just heat the water directly, and use it in a steam turbine. What am I missing here?
    • Because high pressure steam is much harder to manage than the hot oil. High pressure steam lines, boilers, etc. Hot oil is low pressure and can be pumped with a circulating pump.
      • Could they not just heat the 'combustion' chamber itself?

        • Re: (Score:2)

          by emt377 ( 610337 )

          Could they not just heat the 'combustion' chamber itself?

          This would probably give poor timing control over the vapor explosion.

          • Re: (Score:1)

            by Anonymous Coward

            I don't see why it would; you'd just time the water injection (like diesel).

    • Re:Why bother with the oil? (Score:5, Informative)

      by vlm ( 69642 ) on Sunday November 25, 2012 @10:00AM (#42086861)

      It's not being burned, it's only being used as a heat carrier. Seems to me it would be more efficient to just heat the water directly, and use it in a steam turbine. What am I missing here?

      The hydraulics. I can't be bothered to crack open a steam table at this time of day, but a substantial sized tank of stored 500F water is going to be ridiculously thick walled and heavy... 500F oil can be more or less unpressurized.

      Reading the article I'm not sure what "oil" they're using. Cheap canola oil isn't going to like 500F however asphalt isn't going to like being piped around at room temp.

      The journalist articles don't detail it, but stereotypically there is a huge insulated front end tank being heated by panels so you can run the engine at midnight. Usually its a couple orders of magnitude cheaper to redesign the system to not require operation at midnight, but thats a higher level system failure.

      • Usually its a couple orders of magnitude cheaper to redesign the system to not require operation at midnight, but thats a higher level system failure.

        In the near term, for residential power production I think the best method is to use the grid for "storage". The system would need to be able to gracefully shut down and restart without human intervention, though. PV handles that very gracefully and naturally, this would have to be engineered for it.

      • Synthetic engine oil is good up to 500F, yet can still be pumped around at -40F.
    • It's the flash heating of the water into steam in the cylinder which creates the pressure to drive the piston. Using oil as the heat carrier is simply how they've chosen to concentrate as much heat as possible into a small volume with high surface area as a liquid. The only other way to achieve this would be to heat the edges of the cylinder to much higher temperatures (as they're solid and have low surface area so they don't transfer heat as well) which would likely damage them and reduce efficiency.
  • ... that Slashdot had been finally invaded by the 'run your ICE-powered device on water' fraudsters who are all over the car forums on the web now. Thankful to find its just a bad description of using steam expansion as part of a power stroke (BMW tested the same theory using steam generated or augmented by the engines cooling system a few years back, although it worked for them they couldnt get the costs of it to be viable)

    For the record before anyone does start talking about vehicle water injection, i

    • Re: (Score:2)

      by bosef1 ( 208943 )

      I thought I had seen some proposals for water injection where the water was only injected during full-power operation, where it would help keep the combustion chamber cool, and boiling the water would put more combustion energy into mechanical work instead of just heat. I agree that using it full-time would have its drawbacks.

      • It's somewhat commonly used with diesels, you inject it only when exhaust gas temperatures are high. its function is to reduce temperatures but it also gives you a power boost under maximum load conditions because the water changes state -- which is why it's so effective at removing heat. you can build a poor man's system with a pump and nozzles from AEM for about three hundred bucks, and a set-point controller like the Auber Instruments 1812, 1813 etc for about five bucks. They sell the controllers as 1/8

      • Water injection dates back to the 1920s. It was used because the technology of the day could not use high compression ratios without detonation. Modern technology overcomes detonation by attention to fuel, gas flow, thermal design and ignition timing. Water injection is obsolete.
        • It's still used in some crazy high performance engines. Both the Subaru Impreza and the Ford Focus in WRC used water injection. Can't get results for newer rally cars, but I don't think WRC teams put their current engine specs up on the internet. Those engines typically last around 100 hours, though.

    • For the record before anyone does start talking about vehicle water injection, it adds no power per se...

      In the early days, it was used in jet engines to increase thrust due to the increased expansion value and mass of the discharged exhaust.

      • Re: (Score:1)

        by CdBee ( 742846 )
        I should have said that I meant automobile use - and specifically in reciprocating cylinder engines. The use of water injection on both piston and jet engines has proven benefits, however water injection kit is often sold nowadays under dishonest premises such as calling it 'water fuelling' and claiming notable reductions in petrol or diesel consumption. If it was marketed as a protective measure to prevent overheating I'd have fewer objections to the tactic, despite my reservations about retrofitting such

  • There is a FAQ here: (Score:5, Informative)

    by Tapewolf ( 1639955 ) on Sunday November 25, 2012 @09:55AM (#42086827)

    The last comment at the bottom of the article is a post by one of the project team, linking to a FAQ written in response to the comments.

    http://hydroice.wordpress.com/ [wordpress.com]

  • But I see it's already covered. Cute idea but like programming languages, there's thousands of cute engine designes that aren't practical for widespread use.
  • Instead of oil use liquid sodium! It would be way more efficient!

  • Could use any form of heat; combustion isn't bad (Score:3)

    by caseih ( 160668 ) on Sunday November 25, 2012 @10:23AM (#42086977)

    Most people think of "solar" or "wind" as renewable, but in fact, burning straw pellets could also work very well as a heat source and be carbon neutral (renewable). The nice thing about an engine like this is that any form of heat could drive it. Separating combustion from from the pressures in the engine also will eliminate NOx and other pollutants. So even if the solar part doesn't work out (or at night), this idea still has potential for carbon-neutral energy from just about any heat source that can heat up the oil.

  • Cute idea, but... (Score:5, Interesting)

    by Phydeaux314 ( 866996 ) on Sunday November 25, 2012 @10:47AM (#42087103)

    ...I see a few issues, some fixable, some less so.

    First, while removing the boiler from the whole "steam plant" equation really does help the safety side of things, you have to be VERY VERY SURE that your separator removes ALL the water from your exhaust. Why? Because if you have even a tiny bit of water in your oil tank, and your heat it to 700F, it's going to boil and expand... and suddenly your low-pressure oil reservoir systems just turned into a really weak boiler full of oil that's hot enough to burst into flames. Instead of venting superheated invisible steam that can strip flesh from bones in seconds, you're going to be spurting oil around at temperatures that cause spontaneous combustion when meeting atmospheric oxygen. Not sure if that's really a step up.

    Second, while oil and water don't mix, they do tend to form a really annoying to work with mayonnaise-like suspension of oil globules in water when mixed together really well. This takes a long time - or a lot of energy - to completely split apart.

    Third, in addition to the previous problems with separating mayonnaise, heat dissipation will be an issue. Internal combustion engines carry a LOT of their waste heat away with exhaust, but in a closed-loop system like the one they're proposing here you need to remove the 85% of the energy you don't convert into work. Steamboats traditionally do this with a condenser that sits in the water, but if you're not near a large body of water, well... let's just say your condensing apparatus is going to be a huge, complicated, and difficult to work with because even if you don't have a high-pressure steam BOILER you're still going to have a high-pressure steam CONDENSER.

    You could, of course, run the oil at a cooler temperature... but that drastically cuts back on your efficiency, because your power depends on having a lot of pressure inside the cylinder, and that pressure comes from the steam, and the pressure of the steam depends on the temperature... well, you get the idea. Basic thermodynamics.

    So anyway. It's a cute idea, but unless they've got some really amazing tricks to solve the glaring technical fiddly parts I don't think it's going to get very far. I hope I'm wrong... but I don't think I am.

    • in a closed-loop system like the one they're proposing here you need to remove the 85% of the energy you don't convert into work

      Why? It seems to me that in a system like this one the ideal temperature for the injected water would be just below the boiling point. Retaining heat in the water would reduce the amount of energy you need to inject in the form of hot oil for the same power stroke. The ratio and amount of oil and water to be injected will be highly dependent upon the temperatures of both, but with a computerized control system that doesn't seem like it would be a problem.

    • I should think the water won't last long in the oil as its being heated to 700 degrees, the watter should boill off and be recoverable with a condensor. This is assuming that you would want a closed circuit for the water.

      If the plant isn't efficient as per "energy out" / "energy in" it could still be efficient as per "total energy out lifetime" / "total cost in dollars lifetime".

      • I should think the water won't last long in the oil as its being heated to 700 degrees, the watter should boill off and be recoverable with a condensor.

        Only if the water is still steam when it exits the expansion chamber -- which should be easy enough to achieve by balancing the amount of oil and water injected, taking the temperatures of both into consideration.

    • Re: (Score:2)

      by dasunt ( 249686 )

      When I first read this, I thought it was heating the engine block and then injecting water that flashes to stream, driving the power stroke. (So basically a two cycle engine - when the piston is at the top of the cylinder, water is injected, it flashes to steam, that drives the piston down, and when the piston comes back up on the second stroke, an exhaust valve allows the steam to escape. The exhaust valve closes at the top of the stroke, and the process is repeated.

      That would "consume" water, but would

    • Re: (Score:2)

      by AmiMoJo ( 196126 ) *

      Right, I'm sure they never thought of these things you came up with in less than half an hour.

  • In case anyone thinks this is interesting enough to throw money at it, I got this link from the FAQ page: http://www.indiegogo.com/hydroice [indiegogo.com].

    I thought it was interesting enough to throw it a few bucks. Could be snake oil, but it could also be really cool.

  • This is not a combustion engine, at all. It's an "insert water with hot oil, use generated steam to drive engine, separate back oil and water to reuse" engine.

    The potential efficiency is interesting, and the reduction of generated hydrocarbons compared to a normal motor of the awkwardness of creating and handling lead-acid batteries or other awkward electrical energy storage is also interesting. The difficulty of doing reliable water and oil separation for long periods, at low cost and with low power cost,

    • The difficulty of doing reliable water and oil separation for long periods, at low cost and with low power cost

      Perhaps not so difficult if the water is still steam when it exits the expansion chamber. Then you'd be separating liquid oil from gaseous water (which would then have to be condensed). So the energy cost would essentially just be a bit more waste heat than is absolutely necessary. If you could separate them effectively while liquid you could try to tune the water/oil ratio so that the water flashes to steam but then cools back to just below the boiling point as it expands.

    • No one claimed it is an combustion engine.

      They want to take an internal combustion engine, and run it on water and solar-heated oil instead of gasoline.

      Should I translate that for you?

      Take a standard Diesel Engine. Instead of letting it "breath" air, let it breath heated oil.

      Instead of injecting diesel/gasoline at the appropriated piston position inject water.

      Instead of a gasoline explosion moving the piston you get an explosiv expansion of (water) steam.

      Exhaust the steam, reuse the hot oil.

      Works exactly l

  • A quick review of the Wankel engine also shows that this technology might be better applied there. The engine destroying accidental misfires known to some Wankel designes would not occur, and the problems handling the spark plug or with lubrication also would not apply.

  • Interesting if it works.
    - How hot is this engine going to get (safety)?
    - Insulation? (as he says)
    - Capture of waste heat? Something like this [transpacenergy.com]?
    - How is solar energy transferred to oil? With parabolic trough [wikipedia.org]?
    - Energy loss due to vibration of one piston?
    - Breakdown of oil?
    - Any limit to length of pipe running through collector?

  • The Solar Energy Generating Systems power plants in the Mojave Desert have been using parabolic mirrors to generate electricity via solar heat for nearly 30 years now, using oil as the heat transfer fluid.

    "The sunlight bounces off the mirrors and is directed to a central tube filled with synthetic oil, which heats to over 400 ÂC (750 ÂF). The reflected light focused at the central tube is 71 to 80 times more intense than the ordinary sunlight. The synthetic oil transfers its heat to water, which

  • This format of a heat engine isn't "going" anywhere as it would work only on a stationary position where the sun loading could be high with steerable mirrors. You could use molten oil, water or any material you chose to act as a heat source for a heat expansion engine.

    For mobile uses, it all comes down to kilocalories stored per kilogram. This solution "won't go anywhere" mobile.

  • At this stage in development, efficiency isn't a big deal , unless it can be proven early on that it will always be too horrible compared to alternatives...and that only counts if there are alternatives.
    What is interesting/important is it's potential as (pointed out lots of times in the comments) a steam engine that avoids big boilers and has the same kick as an ICE since it uses the same mechanical layout. Any other heat-driven engines that can do the same? same kick, same overhead?
    reading comments seem
  • Don't get me wrong; it's a good idea, but I don't see its application beyond power plants.
  • People, ICE stands for Internal Combustion Engine. Just because it has cylinders, pistons and valves it does not make it an ICE. It is a closed cycle engine. All the fluids used can be recycled and only heat will be added to them, and the mechanical energy extracted from them. Much like nuclear power plants. But piston/value thingies are much less efficient than gas/steam turbines. The only "innovation" here is to use oil to store the heat of solar energy. Again there are many other "fluids" including molte

Slashdot Top Deals

"Pok pok pok, P'kok!" -- Superchicken

Close