Handhelds

Amazon Debuts Kindle Paperwhite, Kindle Fire HD In 2 Sizes 307

Nerval's Lobster writes "Amazon used a Sept. 6 event in California to debut a range of products, including a front-lit [not back-lit, as originally reported] Kindle e-reader with a higher-resolution screen, an updated Kindle Fire, and the new Kindle Fire HD in two screen sizes. First, Bezos showed off a new version of the Kindle e-reader, the Kindle Paperwhite, complete with a front-lit, higher-resolution screen (221 pixels-per-inch and 25 percent more contrast, according to Amazon). The device weighs 7.5 ounces and is 9.1mm thin; battery life is rated at eight weeks, and the screen brightness is adjustable. He then showed off the updated Kindle Fire, before moving to the Kindle Fire HD, which features a choice of 7-inch or 8.9-inch screens, dual stereo speakers with Dolby Digital Plus, two antennas for better Wi-Fi pickup, and a Texas Instruments OMAP 4470 processor (which Bezos claimed could out-perform the Tegra 3). The Kindle Fire HD's 7-inch version will retail for $199 and ship Sept. 14, while the 8.9-inch version will cost $299 and ship Nov. 20. An 8.9-inch, 4G LTE-enabled version with 32GB storage will be available starting Nov. 20 for $499, paired with a $49.99-a-year data plan."
Businesses

Ask Slashdot: What's Your Take On Stand-Up Desks? 347

An anonymous reader writes "I work at a non-profit that doesn't have the resources to automatically bend to each and every whim. However, I've been told that I can't use a cardboard box to put my computer on, for OSHA and fire prevention reasons. So the choice is, sit down for nine hours each day or else get a standup desk to the tune of 500 bucks or more. Is this worth it? Can I make one myself? Anything to know before I get in deep?" There are lots of home-grown stand-up desks out there (search IKEA Hackers for "stand-up desk" if that's your aesthetic leaning), and some ready-made ones from plainish to very expensive. If you've used a stand-up desk, what are your thoughts?
Businesses

Cash-Poor Sharp Mortgages Display Factories 111

Sharp is one of the small handful of companies that actually make the LCDs that go into products badged with many other companies' names. Now, itwbennett writes "The company was asked by one of its main banks to put its physical assets, including its Apple screen plant, up as collateral for about $2 billion in emergency loans, according to an IDG News Service report. Sharp expects to lose over $3 billion this fiscal year."
Upgrades

Raspberry Pi Revision 2.0 Board Announced 155

An anonymous reader writes "The Raspberry Pi finally saw a release on February 29 this year and is thought to have sold 200,000 units, with a million expected to ship before the year is over. That's a lot of tiny PCs, but it's also been an opportunity for owners to feedback any problems or tweaks they'd like made to the board. The Raspberry Pi Foundation has taken the feedback on board and today announced a revised design is being put into production. The new Raspberry Pi, known as revision 2.0 PCB, is expected to start shipping in the next few weeks. The revision includes a number of changes, but is essentially the same board. To summarize it includes a new reset circuit, a replacement for the reset fuses allowing for more reliable USB hub power, two GPIO pin changes for JTAG debug support, four redundant GPIO signals have been removed, and a new connector has been added for attaching a range of boards including a clock or audio codec. Two of the more easily noticeable changes include a fix that stops the HDMI connection interfering with certain operations of the Raspberry Pi, and the addition of two 2.5mm mounting holes to allow for easier mounting."
Iphone

Apple Says "No" To Releasing New Dock Connector Specs 393

sl4shd0rk writes "According to sources, Apple hasn't offered any specs to developers for the new '9-pin Connector' to be used on the next version of the iPhone. Apple has also said it may use 'licensing agreements and threats of lawsuits' to prevent third-party adapters from hitting the market through at least 2012. There have been suggestions that this tactic is to allow Apple time to leverage competition and reap in revenues of $100 million for every 10 million Dock Connector Adapters it sells for $10. It remains unclear whether Apple will allow third-party developers to release competing alternatives after 2012."
Hardware Hacking

Gamers May Get a Charge Out of the Gauss Rifle 98

Zothecula writes "Well, Patrick Priebe might have outdone himself with this one. In the past, the German cyberpunk weapons-maker has brought us such creations as a wrist-mounted mini-crossbow, a laser-sighted rotary-saw-blade-shooting crossbow, and a flame-throwing glove. His latest nasty futuristic device? A video game-inspired electromagnetic weapon, called the Gauss Rifle."
Hardware Hacking

Video Should We Print Guns? Cody R. Wilson Says "Yes" (Video) 444

The Wiki Weapon Project and its idea of making guns with 3D printers has already been mentioned on Slashdot. It has also been written up on Forbes.com and a lot of other geek and non-geek sites. Note that when some Wiki Weapon proponents talk about making "guns" with 3D printers, they may be talking only about lower receivers or other static parts, not barrels, firing pins or other parts that must be machined to close tolerances and are subjected to a lot of stress when the gun fires. But low-cost 3D printing and low-cost CNC machining technologies are both advancing at a rapid rate, so thinking about the intersection of firearm manufacturing and open source is both worthwhile and timely. There's been a strong debate about this topic on Eric S. Raymond's Armed and Dangerous blog that's worth reading. Also recommended: The Home Gunsmith.com and CNC Gunsmithing. Astute Slashdot readers will, no doubt, recommend many more. Meanwhile, this video is about licensing, distribution, and legal matters, not the actual manufacture of firearms. There's a transcript (we're finally doing transcripts of selected videos) below the video for those who prefer to read instead of watch.
Hardware

Submission + - Raspberry Pi revision 2.0 board announced (geek.com)

An anonymous reader writes: The Raspberry Pi finally saw a release on February 29 this year and is thought to have sold 200,000 units, with a million expected to ship before the year is over. That’s a lot of tiny PCs, but it’s also been an opportunity for owners to feedback any problems or tweaks they’d like made to the board. The Raspberry Pi Foundation has taken the feedback on board and today announced a revised design is being put into production. The new Raspberry Pi, known as revision 2.0 PCB, is expected to start shipping in the next few weeks.

The revision includes a number of changes, but is essentially the same board. To summarize it includes a new reset circuit, a replacement for the reset fuses allowing for more reliable USB hub power, two GPIO pin changes for JTAG debug support, four redundant GPIO signals have been removed, and a new connector has been added for attaching a range of boards including a clock or audio codec. Two of the more easily noticeable changes include a fix that stops the HDMI connection interfering with certain operations of the Raspberry Pi, and the addition of two 2.5mm mounting holes to allow for easier mounting.

Hardware

Mass Production of 450mm Wafers Bumped Back Again: 2018 67

Taco Cowboy writes with news on the slipping schedules in the move toward both larger wafers and 3D integrated circuits in the semiconductor fab world. From the articles: "TSMC ... said it planned to start mass-producing next-generation 450mm wafers using advanced 10-nanometer technology in 2018. The advanced 10-nanometer chips could first be used in mobile devices and other consumer electronics, like game consoles, that demand high-performance and low power consumption. The plan was included in the latest technology roadmap unveiled by TSMC about one year after the chipmaker attributed its delay in making 450mm wafers, originally scheduled in 2015, to semiconductor equipment suppliers' postponement in developing advanced equipment for manufacturing amid the industrial slump. Chipmakers can get 2.5 times more chips from a 450mm wafer than from a 300mm wafer ... The industry's gradual migration toward 3D ICs with through-silicon vias (TSV) is unlikely to happen until 2015 or 2016, according to sources at semiconductor companies. Volume production of 3D ICs was previously estimated to take place in 2014. Leading foundries and backend assembly and test service companies have all devoted much of their R&D efforts to TSV development, and are making progress. The major players are believed to be capable of supporting 3D ICs by 2014, but the emerging technology going into commercial production may not take place until around the 2015-16 timeframe." Probably one of the most interesting presentations at HOPE9, "Indistinguishable From Magic: Manufacturing Modern Computer Chips," covered modern semiconductor fabrication and why these things are cool. If you're interested in more background (what do all of those TLAs mean?), check out the slides / audio (or attached video of the presentation from YouTube).
Games

Submission + - Gamers May Get a Charge Out of the Gauss Rifle (gizmag.com)

Zothecula writes: Well, Patrick Priebe might have outdone himself with this one. In the past, the German cyberpunk weapons-maker has brought us such creations as a wrist-mounted mini-crossbow, a laser-sighted rotary-saw-blade-shooting crossbow, and a flame-throwing glove. His latest nasty futuristic device? A video game-inspired electromagnetic weapon, called the Gauss Rifle.
Hardware

Submission + - Mass 450mm wafers production by 2018 (taipeitimes.com)

Taco Cowboy writes: Taiwan Semiconductor Manufacturing Co (TSMC) the world’s top contract chipmaker, yesterday said it planned to start mass-producing next-generation 450mm wafers using advanced 10-nanometer technology in 2018.

The advanced 10-nanometer chips could first be used in mobile devices and other consumer electronics, like game consoles, that demand high-performance and low power consumption.

The plan was included in the latest technology roadmap unveiled by TSMC about one year after the chipmaker attributed its delay in making 450mm wafers, originally scheduled in 2015, to semiconductor equipment suppliers’ postponement in developing advanced equipment for manufacturing amid the industrial slump.

Chipmakers can get 2.5 times more chips from a 450mm wafer than from a 300mm wafer.

Taiwan and South Korea are expected to be the two largest markets for semiconductor equipment this year, with purchases totaling US$9.26 billion and US$11.48 billion respectively, according to SEMI figures.

While in other news, Industry migration to 3D ICs to take place in 2015-16
http://www.digitimes.com/news/a20120904PD209.html

The industry's gradual migration toward 3D ICs with through-silicon vias (TSV) is unlikely to happen until 2015 or 2016, according to sources at semiconductor companies. Volume production of 3D ICs was previously estimated to take place in 2014.

Leading foundries and backend assembly and test service companies have all devoted much of their R&D efforts to TSV development, and are making progress. The major players are believed to be capable of supporting 3D ICs by 2014, but the emerging technology going into commercial production may not take place until around the 2015-16 timeframe.

Intel

Intel Embraces Oil Immersion Cooling For Servers 230

1sockchuck writes "Intel has just concluded a year-long test in which it immersed servers in an oil bath, and has affirmed that the technology is highly efficient and safe for servers. The chipmaker is now working on reference designs, heat sinks and boards that are optimized for immersion cooling. 'We're evaluating how (immersion cooling) can change the way data centers are designed and operated,' said Mike Patterson, senior power and thermal architect at Intel. 'I think it will catch on. It's going to be a slow progression, but it will start in high-performance computing.' Intel's test used technology from Green Revolution Cooling, which says its design eliminates the need for raised flooring, CRAC units or chillers. Other players in immersion cooling include Iceotope and Hardcore (now LiquiCool)."
AI

Social Robots May Gain Legal Rights, Says MIT Researcher 288

dcblogs writes "Social robots — machines with the ability to do grocery shopping, fix dinner and discuss the day's news — may gain limited rights, similar to those granted to pets. Kate Darling, a research specialist at the MIT Media Lab, looks at this broad issue in a recent paper, 'Extending Legal Rights to Social Robots.' 'The Kantian philosophical argument for preventing cruelty to animals is that our actions towards non-humans reflect our morality — if we treat animals in inhumane ways, we become inhumane persons. This logically extends to the treatment of robotic companions. Granting them protection may encourage us and our children to behave in a way that we generally regard as morally correct, or at least in a way that makes our cohabitation more agreeable or efficient.' If a company can make a robot that leaves the factory with rights, the marketing potential, as Darling notes, may be significant."
Games

Valve Job Posting Confirms Hardware Plans 219

redletterdave writes "Valve is reportedly interested in building hardware. The Bellevue, Wash.-based software developer added a job posting to its site on Tuesday morning for an industrial designer. We're frustrated by the lack of innovation in the computer hardware space though, so we're jumping in,' the posting said. 'Even basic input, the keyboard and mouse, haven’t really changed in any meaningful way over the years. There's a real void in the marketplace, and opportunities to create compelling user experiences are being overlooked.'"
Businesses

Submission + - Valve Confirms Hardware Plans (ibtimes.com)

redletterdave writes: "Valve is reportedly interested in building hardware. The Bellevue, Wash.-based software developer added a job posting to its site on Tuesday morning for an industrial designer. "We're frustrated by the lack of innovation in the computer hardware space though, so we're jumping in," the posting said. "There's a real void in the marketplace, and opportunities to create compelling user experiences are being overlooked.""

Slashdot Top Deals